Meyer Sound UPQ2P Narrow Coverage Loudspeaker

Meyer Sound UPQ2P Narrow Coverage Loudspeaker

The self-powered UPQ-2P narrow coverage loudspeaker is a member of the award-winning UltraSeries family of loudspeakers. The UPQ-2P offers extremely high power output and low distortion, as well a focused beamwidth, which make it an ideal solution for small to mid-sized venues, houses of worship, theatres, and nightclubs as either a stand-alone loudspeaker or as part of an array. The loudspeaker’s extended low-frequency headroom delivers a smooth sound over a wide operating frequency range of 55 Hz to 18 kHz. With its intuitive and versatile QuickFly rigging options, the UPQ-2P fits smartly into touring and rental solutions or fixed applications.

Features:

• Narrow pattern affords precise coverage and arrayability
• Extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
• Integral pole mount and quick and easy QuickFly mounting options
• Constant-Q horn affords uniform response throughout coverage area
• Exceptional size to power ratio
• Consistent and predictable performance ensures accurate system design

Specifications:

• Acoustical
  • Operating Frequency Range: 55 Hz 18 kHz
  • Frequency Response: 60 Hz 16 kHz 4 dB
  • Phase Response: 490 Hz 16 kHz 45
  • Maximum Peak SPL: 136 dB
  • Dynamic Range: >110 dB
• Coverage
  • 50 horizontal x 50 vertical (6 dB)
  • 60 horizontal x 60 vertical (10 dB)
• Crossover
  • 690 Hz
• Transducers
  • Low Frequency:
    High-power 15″ cone driver with neodymium magnet Nominal impedance: 2 Voice coil size: 4″ Power handling capability: 1200 W (AES)
  • High Frequency:
    4″ compression driver Nominal impedance: 8 Voice coil size: 4″ Diaphragm size: 4″ Exit size: 1.5″ Power handling capability: 250 W (AES)5
• Audio Input
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: 15 V DC, clamped to earth for voltage transient protection
  • Connectors: Female XLR input with male XLR loop output or VEAM all-in-one connector (integrates AC, audio, and network)
  • Input Impedance: 10 k differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 k, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal – (optional polarity reversal switch)
    • Case: Earth ground and chassis
  • DC Blocking: Differential DC blocking up to maximum common mode voltage
  • CMRR: >50 dB, typically 80 dB (50 Hz 500 Hz)
  • RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
  • TIM Filter: Integral to signal processing (<80 kHz)
  • Nominal Input Sensitivity: 0 dBV (1 V rms, 1.4 V pk) continuous average is typically the onset of limiting for pink noise and music
  • Input Level: Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600 to produce maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifiers
  • Type: Two-channel complementary MOSFET output stages (class AB/H)
  • Output Power: 1275 W (1 x 1000 W, 1 x 275 W)
  • Total Output: 2550 W pea
  • THD, IM, TIM: <.02 %
  • Load Capacity: 2 low channel, 8 high channel
  • Cooling: Convection at low to mid audio levels; fan-assisted only at high audio levels
• AC Power
  • Connector: PowerCon with looping output or VEAM
  • Voltage Selection: Automatic, two ranges, each with high-low voltage tap (uninterrupted)
  • Safety Agency Rated Operating Range: 95125 V AC; 208235 V AC, 50/60 Hz
  • Current Draw:
    • Idle Current: 0.50 A rms (115 V AC); 0.28 A rms (230 V AC); 0.56 A rms (100 V AC)
    • Max Long-Term Continuous Current (>10 sec): 3.90 A rms (115 V AC); 2.00 A rms (230 V AC); 4.40 A rms (100 V AC)
    • Burst Current (<1 sec): 7.0 A rms (115 V AC); 3.9 A rms (230 V AC); 8.2 A rms (100 V AC)
    • Ultimate Short-Term Peak Current Draw: 18.0 A pk (115 V AC); 10.5 A pk (230 V AC); 20.0 A pk (100 V AC)
    • Inrush Current: 6.0 A pk (115 V AC); 8.4 A pk (230 V AC); 7.1 A pk (100 V AC)
• RMS Network (Optional)
  • Equipped for two-conductor twisted-pair network, reporting all amplifier operating parameters to system operators host computer.
• Physical
  • Dimensions:
    • 19.00″ w x 28.27″ h x 18.18″ d
    • (483 mm x 718 mm x 462 mm)
  • Weight: 108 lbs (49 kg)
  • Enclosure: Multiply hardwood
  • Finish: Black textured
  • Protective Grille: Powder-coated hex-stamped steel, black mesh screen
  • Rigging: Aluminum end plates on top and bottom with metric M10 threaded points; integral 1-1/2″ (38 mm) pole mount receptacle on bottom